- What can go wrong with a chimney?
- How is a chimney attached to a house?
- Is a leaning chimney dangerous?
- How do I fill the gap between my house and chimney?
- Can you have 2 fireplaces one chimney?
- What is a chimney corbel?
- Why do old chimneys lean?
- Why are chimneys so tall?
- How much does it cost to fix a chimney leaning?
- Can you put two flues one chimney?
- Can two wood stoves share a chimney?
- Why are chimneys not straight?
- How do you straighten a leaning chimney?
- Do chimneys have to be straight?
- Why do I have 2 chimneys?
- Can a chimney go sideways?
- What to do if chimney is separating from house?
What can go wrong with a chimney?
Some common chimney problems are: chimney obstruction, creosote, brickwork problems, chimney crown and cap, and cracks in the flue.Obstruction.
Chimney Crown and Chimney Cap.
Cracks in the Flue..
How is a chimney attached to a house?
If the house is sided with brick, the chimney can be bonded directly to the brickwork. … I’ve had these straps made at a metal shop and prebent to the measurements of the chimney. The straps extend to each side far enough that they can be lagged into the wall framing.
Is a leaning chimney dangerous?
A leaning chimney is a serious structural problem that should be dealt with immediately. … Water and bugs could get into the gap where the chimney has pulled away from the siding. The chimney liner may be cracked, leaking combustible gases into your home, creating danger for your family.
How do I fill the gap between my house and chimney?
Beth, If the crack is over about 3/8″ you may want to use some type of filler behind the caulk. A light application of canned foam will be easy to work with. Just be sure to use blue tape around the siding and brick edges before filling the crack with the foam (closed cell type).
Can you have 2 fireplaces one chimney?
Fireplaces on multiple levels can also share one chimney structure. … Each fireplace can face the same direction, if you want, since they will not block each other. You might even choose to combine a multi-level fireplace with a double sided fireplace, combining three fireplaces into one chimney.
What is a chimney corbel?
A corbel is a structural piece of stone, wood or metal protruding from a wall to carry weight. A chimney corbel, in very simple terms, is a brick bump-out. You will find essential chimney corbelling in the smoke chamber or on a multi-flue outside wall chimney, this area is also known as a shoulder.
Why do old chimneys lean?
As the smoke from the fire rises up the flue it will cool and condense on the inside surface of the chimney. … Because slightly more occurs on the North side than the South, the North of the Chimney gets fractionally taller and hey presto, it leans to the South.
Why are chimneys so tall?
The height of a chimney influences its ability to transfer flue gases to the external environment via stack effect. … In the case of chemically aggressive output, a sufficiently tall chimney can allow for partial or complete self-neutralization of airborne chemicals before they reach ground level.
How much does it cost to fix a chimney leaning?
Leaning Chimney Repair Cost Leaning chimneys typically cost $3,000 to fix. Oftentimes, a leaning or tilted chimney stack indicates an issue with the foundation. A contractor will find out if it’s a foundation issue by checking whether or not the chimney has level horizontal mortar joints.
Can you put two flues one chimney?
A single chimney can safely have multiple flues inside the chimney, each flue venting an appliance, fireplace, or other device, provided that the chimney was properly constructed, including the necessary spacing or sealant between the individual flues.
Can two wood stoves share a chimney?
Combination Wood / Oil Fired Appliances on Same Floor May Share a Common Flue. A wood-fired heating appliance may be vented into the same chimney flue as an oil-fired heating appliance provided that they are on the same floor – in some jurisdictions.
Why are chimneys not straight?
Efficient Exhaust of Byproducts The hotter the temperature inside the flue, the more efficiently gases will be conducted up and out of the house. … Bends, or offsets, in the flue can retard the steady outflow of gases. They also interfere with the flow of oxygen through the chimney to the fire.
How do you straighten a leaning chimney?
The repair that is most used today for leaning chimney is helical piers. These piers are driven under the leaning chimney until it reaches a good soil base. Brackets are placed on the helical piers under the chimney footing. Then a hydraulic jack slowly lifts the chimney up to its proper position.
Do chimneys have to be straight?
6 Answers from MyBuilder Chimney & Fireplace Specialists The straighter the chimney the better it works and at least 80% of the chimney must be vertical. In a factory made system (twin wall flue) there can be a maximum of 4 bends with a 45 degree bend counting as one and a 90 degree bend counting as two.
Why do I have 2 chimneys?
A flue is a venting system, each system needs its own so If you heat your home with oil or gas and have a fireplace you would have two flues. Often times they are in one chimney so if you were to look down the chimney it would be separated into two venting system inside one chimney.
Can a chimney go sideways?
A wood burning flue cannot run horizontally, only the stove pipe and the snout of a Tee is allowed to. The chimney is only allowed to elbow at 30 degrees off vertical, and has to terminate vertically. … It’s just a fire, burn it!
What to do if chimney is separating from house?
A common and cheaper temporary fix that could have been done to hold the chimney in place is to fill the gap between the leaning chimney and main house structure with mortar or some type of caulking or expanding foam insulation. The chimney could also be fastened into place with metal straps.